sha256: 93b226f20e803667bd1e1ac5644edd0ea41ccf57d300bfb4eec7e630f12d6e3e
C H A N G E L O G
Please note: Only use the firmware file in connection with the current software-version of the CCUx!
Device: HmIP-ASIR - Homematic IP Indoor Siren
Company: eQ-3, Maiburger Str. 29, 26789 Leer, Germany
Version 1.4.x - 20180627
** Related Hardware
** Bugfix
- No acoustical and optical signal in case of backup disarm
** Improvement
*
** Comments
*
Version 1.2.x - 20180212
** Related Hardware
** Bugfix
- Cyclic StatusInfo contains wrong RSSI-Value.
- App sequecne counter check area
- Trigger of silent alarm does not trigger Status Info to AP
** Improvement
- Removed virtual channels
- Improved StatusInfo and ACK Handling
- Improvements for Security Solution Pro:
- Added Backup Channel (Channel 2) with parameters for alarmtype, duration, silent alarm and sd-multicast.
- Added arming of up to seven alarm zones to Direct Execution Command.
- CSC can be send to Channel 2 with ALARM_MODE bitfield as decision value.
- Improved sabotage detection: if one or more zones are armed in case of sabotage, the alarm is triggered internally.
- Added an internal link between Ch 1 and Ch 3 for internal sabotage alarm.
- Changed Status Info with regard to DeviceSpecific Documenation.
- Removed PowerUp Parameters from Ch 3.
- Removed Parameters of ch 1 (sabotage).
- Added Smoke Detector Multicast in case of acoustic alarm for specific zones.
- Added silent alarm mode for specific zones.
- JIRA HMIP_ASIR-48: DISABLE_MSG_TO_AC parameter added
** Comments
*
Version 1.0.9 - 201601213
** Related Hardware
- 1654336B
- Had used the R20 resistor in the PCBA to make sabotage button work well.
** Bugfix
- At DEC with duration bigger then 65s the Device execut the duration not correct
** Improvement
*
** Comments
*
Version 1.0.8 - 201601020
** Related Hardware
- 1654336B
- Had used the R20 resistor in the PCBA to make sabotage button work well.
** Bugfix
- Restart the reciver mode immeditaly in the CB_RX , this bug occur in RC8.
** Improvement
*
** Comments
*
Version 1.0.7 - 20160921
** Related Hardware
- 1654336B
- Had used the R20 resistor in the PCBA to make sabotage button work well.
** Bugfix
- Delete the LED signal while the sabotage button release or press. For security case.
** Improvement
- Improvement the switch time out for all case.
** Comments
*
Version 1.0.6 - 201607027
** Related Hardware
- 1654336B
- Had used the R20 resistor in the PCBA to make sabotage button work well.
** Bugfix
- Corrected the ARR-timeout with sending status-frames.
- Corrected a bug with statusinfo sequence counters.
- If the device is not included the sabotage switch is not working anymore.
It also will never retrigger the inclusion process now.
** Improvement
*
** Comments
*
Version 1.0.5 - 201607025
** Related Hardware
- 1654336B
- Had used the R20 resistor in the PCBA to make sabotage button work well.
** Bugfix
- Added sending of Statusmessges to the linked central if
an event from the sabotage button is recognized.
- Removed sending of config update request frames on
sabotage button if there is no partner because a
statusmessage has been triggered and is enough.
- Statusmessaeges are now send with ARR bit.
** Improvement
*
** Comments
*
Version 1.0.4 - 201607018
** Related Hardware
- 1654336B
- Had used the R20 resistor in the PCBA to make sabotage button work well.
** Bugfix
- ARR Timeout is ignored
- Fixed the bug of : statusinfo with ARR bit, no timeout. Add timeout for this.
** Improvement
- Changed EMC target. add some predefine in it.
** Comments
*
Version 1.0.2 - 201607013
** Related Hardware
- 1654336B
- Had used the R20 resistor in the PCBA to make sabotage button work well.
** Bugfix
** Improvement
- Delete some unused code and perdefine in the code.
** Comments
*
--- END OF FILE ---