sha256: 9908ec0afbd62e151cfda4cd24868b8c76f8a7d3219f53d9547f3d4311b15710
Achtung! Bitte verwenden Sie die Firmware-Datei nur in Verbindung mit der CCU2 ab Version 2.29.18.
Nach dem erfolgreichen Übertragen des Updates ist es erforderlich den HmIP-BDT einmal von der CCU2 ab- und wieder anzulernen, damit alle neuen Funktionen in der CCU2 korrekt angezeigt werden.
Please note: Only use the firmware file in connection with the CCU2 from version 2.25.14.
After the update has been successfully transferred, it is necessary to disconnect the HmIP-BDT from the CCU2 and teach-in the device again. So that all new functions are displayed in the CCU2.
Changelog:
Version 1.4.8 - 20170725
** Related Hardware
** Improvement
- this update inlcludes an update of the dimmer coprocessor
to V1.2.1 to solve flicker errors based on ripple control signals
or other ripple on the mains power
Version 1.4.0 - 20170620
** Related Hardware
** New Feature
- add support of weekprogram and channel lock
** Bugfix
- [HMIP_PDT-8]
[HMIP_BDT-36] - fixed bug that channel keys triggers
every 250 ms an inclusion request frame
- [HMIP_FDT-13] - Check if switch time is valid on current
day was wrong, so switch times are always valid and are
done every day.
- fixed bug on daylight saving time calculation
- The single cast frame with arr after the repeated
multicast frames has to have the same sequence
number as the last multicast frame. So the actuator can
ignore it and only send an app ack.
- [HMIP_BDT-35] - Direct execution commands with speciale
value 0xC9 (old value) is not handled correctly
*[CHANGEMANAGEMENT-51], [HMIP_BDT-43], [HMIP_FDT-16],
[HMIP_PDT-12] - Implement handling of direct
execution commands LOCK and UNLOCK
- [CHANGEMANAGEMENT-25], [HMIP_BDT-42], [HMIP_FDT-15],
[MIP_PDT-11] - Fixed bug, that after sending an
ACK-Frame no ACK frame can be send any more
** Modification
- [HM_ISSUE-159] - add sending of weekprogram status after
inclusion
** Improvement
- handling of sending direct execution command
- this update inlcludes an update of the dimmer coprocessor
to solve flicker errors based on ripple control signals or
other ripple on the mains power
- Update to HMOS 1.20.3
Version 1.2.3 - not released
** Related Hardware
** Bugfix
- [CHANGEMANAGEMENT-19]
[HMIP_BDT-41]
- If dimmer coprocessor is updated on boot, the main
controller tries to set parameters in the dimmer
coprocessor. As this is done immediately after the
dimmer coprocessor update, the application of it is
not ready. Now a timeout doesn't add the task and
the task doesn't try to repeat. If now the stack
tries to validate the new parameters the task denied
validation as the task is not idle -> dead lock
Version 1.2.2 - 20170130
** Related Hardware
** Bugfix
- HMIP_BDT-33 - Fixed Bug that the minimum dimm level is
ignored
Version 1.2.0/1.2.1 - 20170111
** Related Hardware
** New Feature
- add support of HmIP-PDT
- add support of HmIP-FDT
** Improvement
- Update to HMOS V1.18.3
- Update Dimmer Coprocessor to V1.0.13
** Bugfix
- Fixed sending of an answer frame if a sending device (RC
etc.) is connected to more than one virtual channel.
- Changed port pin for band-in-use function (GDO2) as the
HmIP-FDT uses a different pin. Now the MISO pin is used
(universal)
- [HMIP_BDT-30] - If a sending device (RC etc. ) is
connected to more than one virtual channel, only the
first channel is switching. So the missing multichannel
support is added. Multiple real actor channels doesn't
work further.
- If a sending device (RC etc. ) is connected to more than
one virtual channel, only a answer frame is send
instead of a status info ack.
- Handling of direct execution commands ignore level 201
(last level)
- Channel 1 parameters (List 1) are not loaded if they
have changed. They were loaded only after reboot.
- Statusinfo with Update Error is only triggered if device
is already included.
- The over temperature and overload thresholds are not
set, if update task returns with an error -> dimmer
copro is not available
- HMIP_BDT-28 - Modify power up jump targets to match the
power up jump targets of the switch actuators
- HMIP_BDT-31 - Device sends answers on Multicast command
and on commands without arr bit in generally
- add visualization of the real channel state on led
- add parameter LED_DISABLE_CHANNELSTATE to activate
or deactivate the visualisation
Version 1.0.2 - 20160902
** Related Hardware
** Bugfix
- On some devices the switch task is not removed in all
cases, this causes that after an OTAU-Update the device
made a factory reset on every boot. It is not clear why
not all devices are defected by this bug. It might be
depending on timing differences.
Version 1.0.1 - 20160901
** Related Hardware
** Bugfix
- If channel keys are pressed while device is booting
and initializing, the device gets into an "undefined
state. The key callback is now registered if the
booting, copro update and possible configuration of the
internal links are finished.
- If someone tries a factory reset on bootup, the device
might get into a stall. Factory reset on bootup is now
working
Version 1.0.0 - 20160830
** Related Hardware
** Comments
- Release Candidate for first lot.
--- END OF FILE ---
** Bugfix
- <JIRA Vorgangsnummer (optional)> -
- <JIRA Vorgangsnummer (optional)> -
** New Feature
- <JIRA Vorgangsnummer (optional)> -
- <JIRA Vorgangsnummer (optional)> -
** Modification
- <JIRA Vorgangsnummer (optional)> -
- <JIRA Vorgangsnummer (optional)> -
** Improvement
- <JIRA Vorgangsnummer (optional)> -
- <JIRA Vorgangsnummer (optional)> -
** Bugs
- <JIRA Vorgangsnummer (optional)> -
- <JIRA Vorgangsnummer (optional)> -
** Related Hardware
- - <zusätzliche Hinweise, Modifikationen usw.>
** Comments