sha256: 9804a970f60fb492a11d9896725a5a1639a85dc53a7977aa61d7ee1f863c8db7
C H A N G E L O G
Please note: Only use the firmware file in connection with the current software-version of the CCUx!
If the switching actuator is operated in two-point control and the firmware version is 2.18.14,
we recommend to remove the batteries from the wall thermostat until the actuator update has been
successfully done. Otherwise the transmission of the firmware will be interrupted.
Device: HmIP-PSM-PE - Pluggable Switch and Meter
Company: eQ-3, Maiburger Str. 29, 26789 Leer, Germany
Version 1 (2 for pluggable).18.22 - 20210412
** Bugfix
- Device responds on multicast frames without ARR bit
- Device sends Status-Frames with Ack-Flag on SwichCommands without ARR-Flag
Version 1 (2 for pluggable).18.20 - 20210115
** Bugfix
- Fixed a bug that with not removing calibration task.
Version 1 (2 for pluggable).18.18 - 20210106
** Improvement
- Switched to usage of internal OSC with permanent calibraton
from the HFXO due to problems when switching non omic loads.
Version 1 (2 for pluggable).18.16 - 20200803
** Bugfix
- Added missing defines for the new statusinfo module in PS,
thus also in PCBS.
Version 1 (2 for pluggable).18.14 - 20200715
** Bugfix
- Made some routines for testing the relay to ram functions.
Version 1 (2 for pluggable).18.14 - 2020-07-10
** Bugfix
- Device send status continuously and leads CCU and device running into duty cycle
Version 1 (2 for pluggable).18.12 - 20200622
** Bugfix
- After inclusion, device sends bidirectional status telegrams
to the CCU after approx. 120s
Version 1 (2 for pluggable).18.10 - 20200527
** Bugfix
- BSM sends Statusframes with ARR every 3 minutes in case that
SHC did not acknowlegeded
- RSSI-value in AnswerFrame always 0dBm
- BSM does not respond to a keystroke if a switching command was previously
received on the actuator channel from an unknown link partner
** Modification
Version 1 (2 for pluggable).18.6 - 20200309
** Bugfix
- Device sends answers-frame on a TimeInfo from AC to "any-router"-address
- Device sends ack frames if ARR bit is not set
Version 1 (2 for pluggable).18.4 - 20200226
** Bugfix
- Channel keys without function if external link
partner could not be reached and DisableMSGToAC = true
- Device sends status info with "Level with profile Information"
instead of "Binary with profile Information"
- Parameter DisableMSGtoAC without function
if multicast address is set as system partner
- If the button is pressed to fast after restart ,
the device does not switch permanently any more.
Version 1 (2 for pluggable).18.2 - 20200212
** Bugfix
- Device running into duty cycle if CCU or HAP is not available
- Update status info sending rules
- Configuration is not longer shown on LED,
if a key is pressed while getting config data
** New Feature
Version 1 (2 for pluggable).16.0 - 20191121
** Bugfix
- Fixed inverted LEDs in bootloader (V1.14.2)
** Modification
** New Feature
Version 1 (2 for pluggable).15.10 to 15.24 - 20191106
** Bugfix
- HMIP_BSM-79 - If possible, send multicasts only to PARTNER_ALL_WIRED_DEVICES
instead of to PARTNER_ALL_DEVICES.
- HMIP_BSM-84 - Device reboots if relay has to be switched
- fixed bug in device behavior, if message to ac is disabled
- fixed bug if factory reset is aborted
** Modification
- Modify emlib makro calls due to changes in updated emlib
- Update HMOS to 1.43.41
- Update Bootloader to 1.14
** New Feature
- Add support for switch inputs
- Add relay count feature
Version 1 (2 for pluggable).15.8 - 20190522
** Bugfix
- Fixed a bug in the zero crossing module due to new
version of emlib.
Version 1 (2 for pluggable).15.6 - 20190424
** Bugfix
- SH_PSMR_HMIP-14/CHANGEMANAGEMENT-1148 -
PowerUpAction is executed although the parameters
are not yet loaded.
Version 1 (2 for pluggable).15.4 - 20190329
** Bugfix
- HMIP_MOD_OC8-23
HMIP_PCBS-29
HMIP_PCBS_BAT-29
HMIP_PCBS2-14
YOU_SWA_POM_PAI-68
HMIP_BSM-71
HMIP_FSM-32
HMIP_FSM16-25
YOU_SWA_PAI-52 - Modify event counter check to meet current specification
Version 1 (2 for pluggable).15.2 - 20190308
** Bugfix
- HMIP_MOD_OC8-22
HMIP_PCBS-28
HMIP_PCBS2-13
YOU_SWA_POM_PAI-67
HMIP_BSM-73
HMIP_FSM-31
HMIP_FSM16-24
YOU_SWA_PAI-51 - If the switch-on and switch-off times in the Easy
Profile are set to "Not active" at the same time, the device hangs up.
Version 1 (2 for pluggable).15.0 - 20190227
** Bugfix
- FSI16 switches relay to fast if mains power fails (not waiting min
200 ms) as the the ZCD detection without measuring IC produces IRQs
only for positive half waves. Timer now has an interval of 20 ms,
so the relay is switch only if 220 ms has elapsed.
** Comments
Version 1 (2 for pluggable).13.12 - 20181116
** Bugfix
- Fixed another potentially deadlock.
Version 1 (2 for pluggable).13.10 - 20181115
** Bugfix
- HMIP_BSM-67 - Race condition may cause deadlock
** Improvement
- check of keypress counter and application sequence counter updated
** Comments
Version 1 (2 for pluggable).13.8 - 20181026
** Bugfix
- Stopped sending inclusion request on each long keypress
repetition.
Version 1 (2 for pluggable).13.6 - 20180813
** Bugfix
- Corrected sending of Status-Info
frames if the recipent (central or statusinfo receiver)
is not available.
Version 1 (2 for pluggable).13.4 - 20180628
** Bugfix
- Corrected bug with weekprogramm
at the day of daylight changeover.
Version 1 (2 for pluggable).13.2 - 20180622
** Bugfix
- Corrected bug with creating direct
execution frames in the weekprogramm.
Version 1 (2 for pluggable).13.0 - 20180605
** Comments
- Increased version number due to creation of a tag.
Version 1 (2 for pluggable).11.17 - 20180601
** Bugfix
- Increased HMOS version to 1.30.0 to be able to route
inclusion frames (with routing actuators).
** Improvement
- Added functionality and configuration
parameters to do "OFF-Actions" at powerup.
Version 1 (2 for pluggable).11.16 - 20180309
** Comments
- Changed the default
value for the long keypress from 4s to 0,4s. Did necessary
modifications to leave the pairing function as it is.
Version 1 (2 for pluggable).11.14 - 20180223
** Bugfix
- Added reset of measurement array after switching
to prevent next measurement to be outdated. An outdated
array may cause wrong switching!
Version 1 (2 for pluggable).11.12 - 20180216
** Bugfix
- Corrected timeout for sequence counter (from 10 to 2 minutes).
Version 1 (2 for pluggable).11.10 - 20180214
** Bugfix
- Corrected switching direction if switching with current
detection is disabled.
Version 1 (2 for pluggable).11.8 - 20180213
** Bugfix
- Added sending of unknown RSSI value in two cases.
** Improvement
- Added new operation mode (minimum HMOS 1.24.0 necessary)
- Changed counting of event_counter to new mechanism
(boot:0; other:[1..252]).
- Changed checking of event_counter to new mechanism.
Version 1 (2 for pluggable).11.6 - 20180205
** Bugfix
- Fixed wrong reset of a pending flag if disable_msg_to_ac was set.
** Improvement
** Comments
- Changed default value for POWERUP_ONTIME from 0x00 to 0xFF.
Version 1 (2 for pluggable).11.4 - 20171219
** Bugfix
- Fixed bug with fast switching
Version 1 (2 for pluggable).11.2 - 20171103
** Bugfix
- Fixed a bug with sending statusframes with ACK and ARR bit
Version 1 (2 for pluggable).11.0 - 20171013
** Bugfix
- Fixed a bug with sending statusframes at actuartors
with powermeter function.
Version 1 (2 for pluggable).9.2 - 20171006
** Bugfix
- Corrected behaviour of weekprogrammm for neagtive coordiantes.
- Changed behaviour of init routines in powermeter- and switch-task.
- Fixed behaviour of sending statusmessages
for multichannel devices.
Version 1 (2 for pluggable).9.1 - 20170908
** Improvement
- new parameter for suppressing messages to Access Controller
** Comments
- First release version for HmIP-PCBS2
Version 1 (2 for pluggable).8.12 - 20170719
** Bugfix
- Statusmessage handling corrected
** Improvement
- Statusmessage handling optimized for multichannel devices
- No reboot after aborded factory reset
- new telegrams are only send if previous telegram is acked or timed out
** Comments
- First release version for HmIP-MOD-OC8
- Use of bootloader 1.10.0
Version 1 (2 for pluggable).7.6 - 20170530
** Bugfix
- ARR timeout is not observed
with the Info and TimeInformation frames
- LowBat Bit is not set in the status Info
** Improvement
- DataType Operating Voltage send with StatusInfo
Version 1 (2 for pluggable).7.5 - 20170519
** Bugfix
- The device reacts with the same
event counter for an unconditional switch command.
- Device is permanently awake.
Version 1 (2 for pluggable).7.4 - 20170427
** Bugfix
- Fixed a bug with not acting device if the
channel key was pressed at a included device.
Version 1 (2 for pluggable).7.3 - 20170426
** Bugfix
- Increased the power to trigger a simulated
keypress from 0.1W to 1 W.
- Value for the new powerstatus is saved after
being stable for two measurements.
- Corrected default duration of weekprogramm to 0xFF.
- Corrected / Optimised sending of a normal ACK/NACK.
Version 1 (2 for pluggable).7.2 - 20170425
** Comments
- Removed ramp time from the weekprogram.
- Added sending of statusframes for the weekprogram.
(After inclusion, cyclic and on request)
- Corrected a bug with inhibit channels.
Version 1 (2 for pluggable).7.1 - 20170413
** Comments
- Added lock feature to weekprogramm channel.
- Added delayed weekprogram status info to status info
receiver after change of lock channels.
Version 1 (2 for pluggable).7.0 - 20170405
** Bugfix
- Increased the pulse for switching the relais
from 30 ms to 75 ms.
** Comments
- Increased version due to creation of a tag.
Version 1 (2 for pluggable).5.9 - 20170405
** Comments
Version 1 (2 for pluggable).5.8 - 20170328
** Bugfix
- In auto inclusion mode, the triple burst listener device is not a permanent listener.
Version 1 (2 for pluggable).5.7 - 20170308
** Bugfix
- Fixed a bug with the sequence counter in the unicast frame
(for collecting ACKs) after sending multicast frames due
to a long keypress.
Version 1 (2 for pluggable).5.0 - 20161209
** Comments
- Increased version number due to creation of a tag.
Version 1 (2 for pluggable).3.8 - 20161128
** Bugfix
- Corrected a bug with RSSI calculation in statusInfo.
Version 1 (2 for pluggable).3.7 - 20161114
** Bugfix
- Fixed a bug that caused errors with one partner linked
to more channels.
Version 1 (2 for pluggable).3.6 - 20161104
** Bugfix
- Fixed a bug with sending unrequested ACKs.
Version 1 (2 for pluggable).3.5 - 20161021
** Bugfix
*
** Comments
- Added switching the relay as EMC action.
Version 1 (2 for pluggable).3.4 - 20160926
** Bugfix
- Fixed a bug with the simulated keypress generated from
the powermeter task.
Version 1 (2 for pluggable).3.3 - 20160913
** Bugfix
- Added IDLE state to switch task.
- Corrected behaviour of the powerfailure function.
- Corrected behaviour of the overhead function.
- Suppressed sending of StatusInfoFrames if the device is
not included.
- Corrected behaviour of factory reset if the keyVisual is
pressed during powerUp.
Version 1 (2 for pluggable).3.2 - 20160901
** Bugfix
- Included hmos 1.16.2 which fixed a bug with exlusion after inclusion
Version 1 (2 for pluggable).3.1 - 20160721
** Bugfix
- Corrected size of action type.
- Fixed a bug that caused not spawning conditional switch
channel task.
- Fixed setting of the decision value for falling direction
in the conditional switch channel.
Version 1 (2 for pluggable).3.0 - 20160719
** Comments
- Increased version number due to creation of a tag.
Version 1 (2 for pluggable).1.17 - 20160718
** Bugfix
- StutusInfo frames from the switch module can now be send
with ARR-Bit.
StatusInfo frames from the powermeter are still
unidirectional all the time.
Version 1 (2 for pluggable).1.16 - 20160714
** Comments
- Removed sending of config update requests on buttonpress
of the keyvisual for all permanent powered actuators.
Version 1 (2 for pluggable).1.15 - 20160708
** Bugfix
- Fixed bug that first reset step is ready before
the timeout of 4 seconds occur.
- Suppress boot blinking if reset is in progress.
- Fixed a bug with index of parameter arrays if the key
visual is used as channel key.
Version 1 (2 for pluggable).1.14 - 20160704
** Bugfix
- Conditional switch channel gets now removed in idle state.
** Comments
- Set the default values for event delay of output1,
meter and conditional channel from 1 to 3 seconds.
- Powermeter arrays for averaging now always get resetted
if SWITCH_set_level_real() is called.
Version 1 (2 for pluggable).1.13 - 20160616
** Bugfix
- Fixed a bug in evaluation of long keypresses
for the pairing mode.
- Fixed a bug with setting parameters for the
input channel.
** Comments
- Set default value for the longpress time in the
HmIP-PSx devices to 4s.
Version 1 (2 for pluggable).1.12 - 20160613
** Bugfix
** Comments
- Added conditional switch channel.
Version 1 (2 for pluggable).1.11 - 20160531
** Bugfix
- Reset ACCEPT_ANY_DEVICE to 0.
** Comments
- Major version increased to 2.
Minor and Path number will run parallel for all devices.
--- END OF FILE ---