sha256: 06c172b3c4531cbbd6fb8f18d2f0e146a113d8175439fb8b0cc2518630334c4b
C H A N G E L O G
Please note: Only use the firmware file in connection with the current software-version of the CCUx!
Device: HmIPW-DRBl4 - Homematic IP Wired Blind Actuator - 4 channels
Company: eQ-3, Maiburger Str. 29, 26789 Leer, Germany
Version 1.8.4 - 2022-10-19
** Improvement
- General improvements - Code optimisation
Version 1.8.2 - 2021-02-15
** Bugfix
- Section of virtual channels remains in "Move up/down reference run" if all three virtual channels are triggered by Direct Execution Command at startup
Version 1.8.0 - 2021-01-15
** Bugfix
- After a long button press, one channel will sporadically remain permanently supplied with 230 volts.
- After a long keypress the actor runs longer than the set driving time
Version 1.6.0 - 2020-06-26
** Improvement
- Add CHANNEL_OPERATION_MODE to switch between blind and shutter mode
Version 1.4.0 - 2019-09-24
** Bugfix
- Shutters and blinds with longer driving times do not reach end position by short movements (very small values for MAX_TIME_FIRST_DIR)
- If the switch-on and switch-off times in the Easy Profile are set to "Not active" at the same time, the device hangs up.
** Improvement
- Modify event counter check to meet current specification
Version 1.2.10 - 2018-11-07
** Bugfix
- Device doesn't show the supply voltage on display, instead an error is shown
Version 1.2.8 - 2018-11-06
** Bugfix
- Short key press of key visual leads to a restart, if a factory reset was aborted before
- Event counter timeout isn't reset if within the triggered profile the multiexecution flag isn't set
Version 1.2.6 - 2018-09-28
** Bugfix
- Weekprogram sometimes does not trigger all channels
Version 1.2.4 - 2018-08-27
** Bugfix
- If more than one status ACK frame is within the answer queue only the first one is send. Afterwards every new status ACK only triggers the last one
- Statusinfo module creates status ACK telegrams with set ACK, ARR and Boot bits if this is the first status to be sent after startup
- HmIP_APP: Send node confusion when using external send nodes
- Sometimes Statusinfo uses old ApplicationSequenceNumber and Statusinfo with ACK get lost
- Answer-Frames are sometimes sent to the wrong IP destination
Version 1.2.2 - 2018-08-14
** Bugfix
- Real channel does not reach correct final slats position if more than one virtual channel is triggered at same time
- Weekprogram doesn't work correctly if several virtual channels shall be triggered by one switching point
Version 1.2.0 - 2018-08-01
** Bugfix
- configuration of weekprogram channel does not work
- First drive of channel 5, 9 and 13 always takes 90 seconds although the driving time was modified
- Device sends no status info at local operation
- If the link partner is known, an NAK is sent on ("invalid") frames without ARR bit
- If "Disable Message to AC" is activated and only one channel is addressed, no App-Ack is sent.
- Direct Execution Commands without ARR bit are answered at application level
- Homematic IP actuators trigger, due to the astro function, one hour delayed or prematurely on the day of the time changeover.
- Divide maximum number of partners for virtual channels into individual values for virtual A, B and C
- Fix CCM flags according to RFC3610
** Improvement
- All PowerUp parameters, that are listed in list 3 of the device, must be supported.
- Add new parameter for Contrast
- Unify values for undervoltage
--- END OF FILE ---