sha256: 6b67646c1c78610a7aad7c1404fa24d50423bbaf6e9346724cde9e27c0554863
Achtung! Bitte verwenden Sie die Firmware-Datei nur in Verbindung mit der CCU2 ab
Version 2.29.23
Please note: Only use the firmware file in connection with the CCU2 from
Version 2.29.23
Changelog: HmIP-BWTH, HmIP-BWTH24
Version 1.2.004 - 20171123
Version:
Application: 1.2.004
Bootloader: 1.10.000
Library: 1.20.004
** Related Hardware
- HmIP-BWTH: 1664468x, 1454133x, 1333915x, 1333941x, 1333926x
- HmIP-BWTH24: 1664468x, 1454133x, 1714486x, 1333941x, 1714485x
** Bugfix
- Logic "Window open temperature" corrected in cooling mode
In cooling mode, it is not advisable to change to the window open temperature, as
a result, more cooling would have to be used.
- Correction in Paging-Module HMOS-Library
Catched erros which could occure after an OTAU update to a newer paging module.
- Correction for the Optimum Start Stop function
After activating the optimum start stop function it is now executed correctly.
- Antenna symbol synchronization in the display.
If the date and time can be requested by the access point, this is a sign that the
radio communication is in order. The flashing of the antenna symbol should then be
canceled.
- Expansion for inclusion condition.
If parameter changes have been made to the device before the inclusion, the device
can only be included if a factory reset has been performed on the device before.
- Correction for set point temperature update after weekprogram configuration.
If window open is detected (extern/intern) and during this time a new week program
is transmitted to the device, the device updated the set point temperature after
window close by using the new week program set point temperature.
- Function modification during two-point control.
During the two-point control (startup sequence), the device do observe the
parameter values "COOLING_DISABLE" and "HEATING_DISABLE".
- Correction when changing from auto mode to manu mode.
When changing from auto mode to manu mode and boost is active, boost is abort.
- Function modification after removing internal link between channel 8 and channel 10.
When removing the internal link between channel 8 and channel 10 by the access
point, the relay should be deactivated.
- Improvement for the display.
When changing the temperature offset from the App the LCD display should be updated
directly.
- Extension for the Quick Veto Function.
If the quick veto function is active, the remaining time is transferred in the
status telegram.
- Behavior after aborting the factory reset.
If the factory reset is aborted or not executed until the end, the device performs
a reboot after the termination or after the timeout.
- Abort of Quick Veto by "Duration = 0".
If Quick Veto is active, Quick Veto can be aborted by the radio command
"Duration = 0". The device answers the radio telegram with an "Ack".
** Modification
- Change to Version 1.2.004
With the help of the new parameter "DISABLE_MSG_TO_AC" all transmissions to the
central address are suppressed. Also to the status receiver address if this is the
same as the central address.
- Function modification of Optimum-Start-Stop
Change to Optimum Start, means that the comfort temperature should be reached at
the desired point in time, the lowering temperature not.
Version 1.0.011 - earlier
** Related Hardware
- HmIP-BWTH: 1664468x, 1454133x, 1333915x, 1333941x, 1333926x
- HmIP-BWTH24: 1664468x, 1454133x, 1714486x, 1333941x, 1714485x